Skip to content
  • Victron Skylla-i 24V 100A 3 Outputs

Victron Skylla-i 24V 100A 3 Outputs

£2,121.14 £1,334.87 Save 37%

This Victron Skylla-i is a modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air. It has three 100A full rated outputs and one 4A output. Charge voltage can be precisely adjusted to suit any battery system. It’s suitable for both lead acid and lithium battery banks.

  • 100A charging current
  • Suitable for 24V systems
  • 4 outputs (3x 100A + 4A)

Sorry, this product is not available to purchase in your country.

One percent of this purchase goes to planting trees and advancing access to solar energy 🌱
Find out more

Campervan electrics leaving you confused?

Our team of engineers will design your perfect system, bespoke to your needs 👌
Discover more It's free

    A modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air.

    • The right amount of charge for a lead-acid battery: variable absorption time
    • BatterySafe mode: preventing damage due to excessive gassing
    • Storage mode: less maintenance and aging when the battery is not in use
    • Smaller and lighter compared to similar models
    • NMEA 2000 Canbus connection
    • PowerControl: set a maximum shore power
    • Remote Control
    • Li-ion (LiFePo4) ready

    Features

    Skylla-i (3): three full current outputs to charge 3 battery banks

    The Skylla-i (3) features 3 isolated outputs. All outputs can supply the full rated output current.

    Rugged

    Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.

    Flexible

    Next to a CAN bus (NMEA2000) interface, a rotary switch, DIP switches and potentiometers are available to adapt the charge algorithm to a particular battery and its conditions of use.

    Important features:

    Synchronised parallel operation Several chargers can be synchronised with the CAN bus interface. This is achieved by simply interconnecting the chargers with RJ45 UTP-cables. Please see the manual for details.

    The right amount of charge for a lead-acid battery: variable absorption time

    When only shallow discharges occur the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.

    Preventing damage due to excessive gassing: the BatterySafe mode

    If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-i will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached.

    Less maintenance and aging when the battery is not in use: the Storage mode

    The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2 V/cell (26,4 V for 24 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.

    To increase battery life: temperature compensation

    Every Skylla-i comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and/or when important fluctuations of battery temperature are expected.

    Battery voltage sense

    In order to compensate for voltage loss due to cable resistance, the Skylla-i is provided with a voltage sense facility so that the battery always receives the correct charge voltage.

    Suitable for AC and DC supply (AC-DC and DC-DC operation)

    The chargers also accept a DC supply.

    Use as a power supply

    As a result of the perfectly stabilized output voltage, the Skylla-i can be used as a power supply if batteries or large buffer capacitors are not available.

    Li-Ion (LiFePO4) ready

    Simple charger on-off control can be implemented by connecting a relay or open collector optocoupler output from a Li-Ion BMS to the remote control port of the charger. Alternatively complete control of voltage and current can be achieved by connecting to the galvanically isolated CAN bus port.

    Product SKU: SKI024100002


    Weight 7 kg
    Dimensions 40.5 × 25 × 15 cm
    Brand

    Victron Energy

    Manufacturer Part Number

    SKI024100002

    Voltage

    24V

    Current (A)

    100

    Input Voltage

    230V

    Number of Outputs

    3

    Protection Category

    IP21

    Bluetooth Enabled

    No

    Warranty

    5 Years

    Country of Manufacture

    Malaysia

    Product or kit

    Product


    Reviews

    There are no reviews yet

    Be the first to review “Victron Skylla-i 24V 100A 3 Outputs”

    Your email address will not be published. Required fields are marked *

    Overall rating*
    0/5
    * Rating is required
    Rating:*
    0/5
    * Rating is required