Skip to content
  • A blue Victron Smart Battery Protect 100A - 48V device with terminals, indicator lights, and a connector.
  • A blue Victron Smart Battery Protect 100A - 48V device with terminals, status indicator, and connectors.
  • A blue signal isolating protector device, akin to the Victron Smart Battery Protect 100A - 48V, featuring connectors and green terminals on top, labeled "48/1100".

Victron Smart Battery Protect 100A – 48V

£187.92 £142.08 Save 24%

The Victron Smart BatteryProtect is designed to protect a leisure battery in an electrical system. It disconnects the battery from non-essential loads before it is completely discharged, which would damage the battery. The Battery Protect is not designed for reverse currents from charging sources.

  • Suitable for loads up to 100A
  • Suitable for 48V systems
  • Smart model can be connected to using the VictronConnect app

Sorry, this product is not available to purchase in your country.

SKU: BPR110048000 Categories: ,

One percent of this purchase goes to planting trees and advancing access to solar energy 🌱
Find out more

Campervan electrics leaving you confused?

Our team of engineers will design your perfect system, bespoke to your needs 👌
Discover more It's free

    The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.

    When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set.

    Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual).

    If required, Bluetooth can be disabled.

    The Smart BatteryProtect is not designed for reverse currents from charging sources.

    Features

    Protects the battery against excessive discharge and can be used as a system on/off switch

    The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.

    The on/off input can be used as a system on/off switch.

    Bluetooth: programming made easy

    When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set.

    Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual).

    If required, Bluetooth can be disabled.

    A special setting for Li-ion batteries

    In this mode the BatteryProtect can be controlled by the VE.Bus BMS

    Ultra-low current consumption

    This is important in case of Li-ion batteries, especially after low voltage shutdown.

    Please see our Li-ion battery datasheet and the VE.Bus BMS manual for more information.

    Over voltage protection

    To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16.3V respectively 32.6V.

    Ignition proof

    No relays but MOSFET switches, and therefore no sparks.

    Delayed alarm output

    The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay.

    Delayed load disconnect and delayed reconnect

    The load will be disconnected 90 seconds after the battery voltage drops below the preset level. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected.

    The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage.

    Product SKU: BPR110048000


    Weight 0.8 kg
    Dimensions 6.2 × 12.3 × 12 cm
    Brand

    Victron Energy

    Manufacturer Part Number

    BPR110048000

    Voltage

    48V

    Current (A)

    100

    Peak Current (During 30 Seconds)

    250A

    Operating Voltage Range

    24 – 70 V

    Alarm Output Delay

    12 seconds

    Max. Load on Alarm Output

    50mA

    Load Disconnect Delay

    90 seconds

    Protection Category

    Electronics: IP67 (potted), Connections: IP00

    Connection

    M8

    Mounting Torque

    9 Nm

    Bluetooth Enabled

    Yes

    Smart functionality

    Smart

    Warranty

    5 Years

    Country of Manufacture

    India

    Product or kit

    Product


    Reviews

    There are no reviews yet

    Be the first to review “Victron Smart Battery Protect 100A – 48V”

    Your email address will not be published. Required fields are marked *

    Overall rating*
    0/5
    * Rating is required
    Rating:*
    0/5
    * Rating is required